Rexroth PGH5-3X/250RE07VE4 Internal Gear Pump

Overview

The Rexroth PGH5-3X/250RE07VE4 is a frame-size 5, NG 250 internal gear pump with a fixed geometric displacement of 250.50 cm³/rev. This page identifies catalog configuration R901147128 for quotation. Send the complete nameplate and installation details to confirm the required supplied version.

Reviewing the 250 four-hole pressure duty

This 250.50 cm³/rev version uses an E40N keyed shaft and a 160B4SW four-hole flange. Maximum operating pressure is 135 bar; 170 bar is only the brief peak limit. Confirm the required flow, suction arrangement, drive power and pressure cycle for this large-displacement configuration.

Key configuration details

• 250.50 cm³/rev fixed geometric displacement.
• E shaft: cylindrical keyed shaft with through-drive to ISO 3019-2, E40N.
• E4 mounting: Four-hole flange to ISO 3019-2, 160B4SW.
• Material number R901147128 for catalog identification.

3X denotes the component series family. The first R after the size code means clockwise rotation viewed at the shaft end. The next letter, E, specifies a cylindrical keyed shaft with through-drive to ISO 3019-2, E40N. Port code 07 means suction and pressure ports to ISO 6162-1. V indicates FKM shaft seal and seals. E4 mounting: Four-hole flange to ISO 3019-2, 160B4SW.

Technical specifications

Maximum operating pressure: 135 bar. Peak pressure: 170 bar, limited to 10 ms per event and 300 hours total accumulated peak duration. Reference measurements use HLP46 at 50°C and approximately 30 mm²/s. Confirm the limits for the actual fluid and duty; these values are not recommended system settings.

Catalog speed range: 400–3000 rpm. Permissible speed depends on pressure, drive power, oil viscosity and inlet conditions; confirm the operating point before ordering.

Check the installation

• Match the complete nameplate, material number and any additional suffixes.
• Confirm clockwise rotation, the E shaft, coupling and E4 mounting dimensions.
• Verify the pressure and suction port sizes, flange pattern and installation orientation.
• Provide normal and peak pressure, speed, fluid type, viscosity and inlet conditions.

Request a quotation

Please include:

• Required catalog configuration: PGH5-3X/250RE07VE4; material number: R901147128
• Quantity and destination country
• Existing pump nameplate and photographs of the shaft, flange and ports
• Working pressure, pressure cycle, drive speed and required flow
• Hydraulic fluid, operating temperature and installation details
• Required supply condition and requested delivery date

Supply condition, price, availability and delivery terms will be confirmed in the quotation.

Request a quote for PGH5-3X/250RE07VE4

Frequently asked questions

What identifies the PGH5-3X/250RE07VE4 configuration?

Use material number R901147128 with the full type code. It specifies 250.50 cm³/rev displacement, an E shaft and E4 mounting. Confirm the nameplate, additional suffixes and actual mechanical dimensions before ordering.

What pressure limit applies to this size?

The maximum operating pressure is 135 bar. The 170 bar peak limit is only for the specified brief transient conditions. Do not apply the 315 bar operating rating of other sizes to this configuration.

Is the E4 flange the same as U2?

E4 uses four mounting holes under ISO 3019-2. U2 uses a two-hole flange under ISO 3019-1. Verify the pilot, bolt pattern, shaft and coupling alignment before considering a change.

Can I request a quote using PGH5-30/250RE07VE4?

Include that reference with a clear nameplate photograph. This page uses the 3X component-series designation; the precise supplied version and its connections will be confirmed in the quotation.

What is needed to confirm price and availability?

Send the complete identification, quantity, destination and required supply condition. Price, stock, delivery time and warranty terms are confirmed in the quotation.