Product photographs supplied by DENGFENG and matched by the supplied model filenames. Confirm the exact unit, nameplate and configuration with your quotation.
TOKYO KEIKI CR-08 internal gear hydraulic motor, 123 cm³/rev, with 4-bolt flange mounting, 7/8-14 UNF SAE O-ring ports and a 1-1/4 in parallel shaft with square key. External drain; observe the 460 N·m shaft limit.
Include quantity, destination, required condition and delivery date. Pricing and availability are confirmed individually.
Closest listed configurations in TOKYO KEIKI CR. These are comparison references; interchangeability has not been established.
Highlighted rows differ. On small screens, scroll the table sideways.
| Selection factor | This modelCR-08-4S4-30-D-JA-J | CR-08-4P4-30-D-JA-J | CR-09-4S4-30-JA | CR-06-4P4-30-JA-J |
|---|---|---|---|---|
| Displacement | 123 cm³/rev | 123 cm³/rev | 153 cm³/rev | 95 cm³/rev |
| Mounting | 4-bolt flange | 4-bolt flange | 4-bolt flange | 4-bolt flange |
| Shaft | 1-1/4 in parallel shaft with square key | 1-1/4 in parallel shaft with square key | 1-1/4 in parallel shaft with square key | 1-1/4 in parallel shaft with square key |
| Main ports | 7/8-14 UNF main ports with SAE O-ring seals in body | Rc1/2 tapered-thread main ports in body | 7/8-14 UNF main ports with SAE O-ring seals in body | Rc1/2 tapered-thread main ports in body |
| Drain | External drain, Rc1/8 on the main-port side | External drain, Rc1/8 on the main-port side | Internal drain; no external drain port designation | Internal drain; no external drain port designation |
| Distributor | Standard spool distributor | Standard spool distributor | Standard spool distributor | Standard spool distributor |
| Shaft torque limit | 460 N·mApplication and hydraulic braking torque must not exceed the shaft limit even if the family torque table is higher. | 460 N·mApplication and hydraulic braking torque must not exceed the shaft limit even if the family torque table is higher. | 460 N·mApplication and hydraulic braking torque must not exceed the shaft limit even if the family torque table is higher. | 460 N·mApplication and hydraulic braking torque must not exceed the shaft limit even if the family torque table is higher. |
No verified differences are recorded for these comparison fields. Confirm the full nameplate and suffixes before choosing a replacement.
Check displacement, flange, shaft diameter and key or spline. Compare the actual coupling and mounting dimensions before choosing a replacement.
Match main-port threads, drain arrangement and distributor. Check the duty against both the applicable performance curve and the shaft torque limit; a series torque figure may exceed the selected shaft limit.
Manufacturer catalog and model-code reference. Confirm the supplied unit against its nameplate and the applicable manual.
| Brand | TOKYO KEIKI |
|---|---|
| Model number | CR-08-4S4-30-D-JA-J |
| Product type | Low-speed high-torque internal gear hydraulic motor |
| series | CR-08 |
| displacement | 123 cm³/rev |
| mounting | 4-bolt flange |
| Main ports | 7/8-14 UNF main ports with SAE O-ring seals in body |
| shaft | 1-1/4 in parallel shaft with square key |
| Shaft torque limit | 460 N·mApplication and hydraulic braking torque must not exceed the shaft limit even if the family torque table is higher. |
| drain | External drain, Rc1/8 on the main-port side |
| distributor | Standard spool distributor |
| rotation | Viewed from shaft: A inlet gives left rotation; B inlet gives right rotationApplies to the listed code without L. |
| Design number | 30 |
| Tachometer connection | None (T code omitted) |
These values describe the catalog series. Permissible operation also depends on the model configuration and the conditions stated below.
| Rated pressure | 21 MPaActual permissible loading is also limited by shaft torque. |
|---|---|
| Instantaneous maximum pressure | 28 MPaInstantaneous maximum, not continuous operating rating. |
| Rated flow | 60 L/min |
| Instantaneous maximum flow | 80 L/minInstantaneous maximum, not continuous rating. |
| Series rated torque | 360 N·mNot an exact-unit usable torque rating; apply shaft limit. |
| Series instantaneous torque | 480 N·mNot continuous; apply shaft limit. |
| Series rated speed | 395 min⁻¹ |
| Maximum back pressure | 7 MPa |
| Catalog flange-type mass | 11.3 kgCatalog flange version mass; actual configuration should be checked. |
Reference information reviewed September 2026. Check the applicable revision for your equipment.
Low-speed high-torque internal gear hydraulic motor
Low-speed high-torque internal gear hydraulic motor
Low-speed high-torque internal gear hydraulic motor
Send us the full model number or a photo of your nameplate.
